Chroma 62015B-15-90 DC Power Supply Module, 15V, 90A, 1350W

Chroma 62015B-15-90 DC Power Supply Module

RENT CHROMA 62015B-15-90 (call for availability)

The Chroma 62015B-15-90 DC Power Supply Module is meticulously engineered for a variety of burn-in applications including LCD panels, DC-DC converters, power inverters, notebook computers, battery chargers, and a host of other electronic devices. Its exceptional high power density and low current ripple provide a cost-effective solution for rigorous power testing requirements. Furthermore, its advanced power factor correction circuitry is designed to comply with IEC standards, ensuring reliable and efficient performance.

Key Features:

• N+1 Redundancy
• Hot-Swappable Maintenance
• Ideal for Burn-in and Plating Applications
• High Power Applications with CSU
• Remote Sense Capabilities
• Remote ON/OFF Functionality
• CAN Bus Control Interface
• DC OK Signal Output
• Voltage Range: 1 ~ 15V
• Current Range: Up to 2000A (System)
• Power Range: Up to 1.5KW per module, up to 120KW per system
• High Power Density: 464 mW/cm³ (7.13 W/in³)

Specifications:

• Electrical Specifications:
  • Output Ratings:
    • Output Power: 1350W
    • Output Voltage: 1~15V
    • Output Current: 1~90A
  • Line Regulation: 0.1% FS
  • Load Regulation: 1% FS
  • Programming Accuracy: 1% FS
  • Measurement Accuracy: 1% FS
  • Output Noise (20MHz):
    • Voltage Noise (P-P): 100mV
    • Voltage Ripple (rms): 30mV
    • Current Ripple (rms): 0.9A
  • Efficiency: > 87% @ full load
  • Turn On Overshoot Voltage (Rise Time of 100ms): 5% of nominal output
  • Transient Response Time: < 5 ms
  • AC Input Voltage:
    • Six Position Mainframe: 187 ~ 250 Vac (3 Phase 4 Wire, Δ Connection) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) / 45 ~ 65 Hz
    • Three Position Mainframe: 187 to 250 Vac (single phase) / 45 ~ 65 Hz
    • Input Power Factor: > 0.98 @ full load
• Protection Functions:
  • OVP: Automatically shuts down at 115% of set value
  • Adjustment Range: 1~16V
  • OCP: Current limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.
  • OTP: Automatically shuts down if internal limit is reached
• I/O Signal:
  • Remote ON/OFF (I/P): Dry contact (closed = enabled), vice versa
  • AUX Voltage: 4 ~ 24V / 0.5A at mainframe (by trimmer adjust voltage)
  • DC OK Signal Type (O/P): Dry contact (closed = enabled) (Error: OVP / OCP / OTP / AC Fault)
• Programming Response Time (Six Position Mainframe through CAN):
  • Rise Time (Full Load): For a programmed 5% to 95% step in output voltage: 100ms
  • Rise Time (No Load): For a programmed 5% to 95% step in output voltage: 100ms
  • Fall Time (Full Load): For a programmed 95% to 5% step in output voltage: 40ms
  • Fall Time (No Load): For a programmed 95% to 5% step in output voltage: 5s
  • Vout Setting: CAN Bus send command to DC module receiver: 1s
  • Measurement V & I: Under CAN command using fetch: 100ms
  • Delay Time: For output ON/OFF enable and disable (under CAN command): 5s (Single Mainframe)
• General Specifications:
  • Remote Sensing: 3V maximum line loss compensation
  • Parallel Operation: Current Sharing (±5%)
  • Operating Temperature: 0 ~ 50°C
  • Humidity Range: 0 ~ 90% RH, Non-condensing
  • Remote Interface: CAN Bus (optional)
  • Safety & EMC: CE