Chroma 62015B-30-50 DC Power Supply Module

RENT CHROMA 62015B-30-50 (call for availability)

The Chroma 62015B-30-50 DC Power Supply Module is specifically engineered for demanding burn-in applications, catering to LCD panels, DC-DC converters, power inverters, notebook computers, battery chargers, and a variety of electronic devices. Its remarkable high power density and minimized current ripple present a cost-effective solution for all your power supply needs, ensuring compliance with IEC requirements thanks to its advanced power factor correction circuitry.

Key Features:

• N+1 Redundancy for enhanced reliability
• Hot-Swappable Maintenance, enabling easy upkeep
• Optimized for Burn-in and Plating applications
• Supports high power applications with CSU capability
• Remote Sense functionality for precise voltage measurements
• Remote ON/OFF control for flexible operations
• CAN Bus control interface for modern connectivity
• DC OK Signal Output for monitoring
• Voltage range from 1 to 30V
• Current range up to 2000A (system level)
• Power capacity of up to 1.5KW per module, scalable to 120KW per system
• High Power Density rated at 464 mW/cm³ (7.13 W/In³)

Specifications:

Electrical Specifications:

• Output Ratings:
  • Output Power: 1500W
  • Output Voltage: 1~30V
  • Output Current: 1~50A
• Line Regulation: 0.1% FS
• Load Regulation: 1% FS
• Programming Accuracy: 1% FS
• Measurement Accuracy: 1% FS
• Output Noise (20MHz):
  • Voltage Noise (P-P): 100mV
  • Voltage Ripple (rms): 30mV
  • Current Ripple (rms): 0.5A
• Efficiency: > 88% @ full load
• Turn On Overshoot Voltage (10ms rise time): 5% of nominal output
• Transient Response Time: < 5 ms
• AC Input Voltage:
  • Six Position Mainframe: 187 ~ 250 Vac (3 Phase 4 Wire, Δ Connection) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) / 45 ~ 65 Hz
  • Three Position Mainframe: 187 to 250 Vac (single phase) / 45 ~ 65 Hz
  • Input Power Factor: > 0.98 @ full load

Protection Function:

• OVP: Automatically shuts down at 115% of set value
• Adjustment Range: 1~31V
• OCP: Current limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.
• OTP: Automatically shuts down if internal limit is reached

I/O signals:

• Remote ON/OFF (I/P): Dry contact (closed = enabled)
• AUX Voltage: 4 ~ 24V / 0.5A at mainframe (adjustable)
• DC OK Signal Type (O/P): Dry contact (closed = enabled; Error: OVP/OCP/OTP/AC Fault)

Programming Response Time (via CAN):

• Rise Time (Full Load): 100ms for a programmed 5% to 95% step in output voltage
• Rise Time (No Load): 100ms for a programmed 5% to 95% step in output voltage
• Fall Time (Full Load): 40ms for a programmed 95% to 5% step in output voltage
• Fall Time (No Load): 5s for a programmed 95% to 5% step in output voltage
• Vout Setting: 1s for CAN Bus command to DC module receiver
• Measurement V & I: 100ms under CAN command using fetch
• Delay Time: 5s for output ON/OFF enable and disable (under CAN command)

General Specifications:

• Remote Sensing: 3V maximum line loss compensation
• Parallel Operation: Current Sharing (±5%)
• Operating Temperature: 0 ~ 50°C
• Humidity Range: 0 ~ 90% RH, Non-condensing
• Remote Interface: CAN Bus (optional)
• Safety & EMC: CE certified