RENT Chroma 62015B-60-25 (call for availability)

The Chroma 62015B-60-25 DC Power Supply Module is meticulously engineered to excel in burn-in applications for a diverse range of electronic devices, including LCD panels, DC-DC converters, power inverters, notebook computers, and battery chargers. With impressive power density and minimal current ripple, this module stands out as a cost-effective solution for high-performance needs. Incorporating modern power factor correction circuitry, it adheres to IEC requirements, ensuring reliability and efficiency.

Features of the Chroma 62015B-60-25 DC Power Supply Module:

• N+1 Redundancy
• Hot-Swappable Maintenance
• Ideal for Burn-in and Plating
• High Power Applications with CSU
• Remote Sense Capability
• Remote ON / OFF Control
• CAN Bus Control Interface
• DC OK Signal Output
• Voltage Range: 1 ~ 60V
• Current Range: Up to 2000A (System)
• Power Range: Up to 1.5KW per module, up to 120KW per system
• High Power Density: 464 mW/cm³ (7.13 W/in³)

Specifications:

Electrical Specifications:

• Output Ratings:
  • Output Power: 1500W
  • Output Voltage: 1 ~ 60V
  • Output Current: 1 ~ 25A
• Line Regulation: 0.1% FS
• Load Regulation: 1% FS
• Programming Accuracy: 1% FS
• Measurement Accuracy: 1% FS
• Output Noise (20MHz):
  • Voltage Noise (P-P): 200mV
  • Voltage Ripple (rms): 50mV
  • Current Ripple (rms): 0.25A
• Efficiency: > 88% @ full load
• Turn On Overshoot Voltage (Rise Time of 100ms): 5% of nominal output
• Transient Response Time: < 5 ms
• AC Input Voltage:
  • Six Position Mainframe: 187 ~ 250 Vac (3 Phase 4 Wire, Δ Connection) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) / 45 ~ 65 Hz
  • Three Position Mainframe: 187 to 250 Vac (single phase) / 45 ~ 65 Hz
  • Input Power Factor: > 0.98 @ full load

Protection Features:

• OVP: Automatically shuts down at 115% of set value
• Adjustment Range: 1 ~ 65V
• OCP: Current limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.
• OTP: Automatically shuts down if internal limit is reached

I/O Signal:

• Remote ON/OFF (I/P): Dry contact (closed = enabled), vice versa
• AUX Voltage: 4 ~ 24V / 0.5A at mainframe (by trimmer adjust voltage)
• DC OK Signal Type (O/P): Dry contact (closed = enabled) (Error: OVP / OCP / OTP / AC Fault)

Programming Response Time (Six Position Mainframe through CAN):

• Rise Time (Full Load): 100ms for a programmed 5% to 95% step in output voltage
• Rise Time (No Load): 100ms for a programmed 5% to 95% step in output voltage
• Fall Time (Full Load): 40ms for a programmed 95% to 5% step in output voltage
• Fall Time (No Load): 5s for a programmed 95% to 5% step in output voltage
• Vout Setting: CAN Bus send command to DC module receiver: 1s
• Measurement V & I: Under CAN command using fetch: 100ms
• Delay Time: 5s for output ON/OFF enable and disable (under CAN command) for single mainframe

General Specifications:

• Remote Sensing: 3V maximum line loss compensation
• Parallel Operation: Current Sharing (±5%)
• Operating Temperature: 0 ~ 50°C
• Humidity Range: 0 ~ 90% RH, non-condensing
• Remote Interface: CAN Bus (optional)
• Safety & EMC: CE Compliant